(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
7 Million Products, 2,000 Brands.
50,000 Stock items for Same Day Ship Out.
50,000 Stock items for Same Day Ship Out.
Tel: (60) 3 7890 6399
9am – 6pm (Mon – Fri), 9am – 1pm (Sat)
All Categories
Categories
- Automation Components
A wide variety of standard and configurable components for factory automation engineers in industries such as automotive, semiconductor, packaging, medical and many more.
- Linear Motion
- Rotary Motion
- Connecting Parts
- Rotary Power Transmission
- Motors
- Conveyors & Material Handling
- Locating, Positioning, Jigs & Fixtures
- Inspection
- Sensors, Switches
- Pneumatics, Hydraulics
- Vacuum Components
- Hydraulic Equipment
- Discharging / Painting Devices
- Pipe, Tubes, Hoses & Fittings
- Modules, Units
- Heaters, Temperature Control
- Framing & Support
- Casters, Leveling Mounts, Posts
- Doors, Cabinet Hardware
- Springs, Shock Absorbers
- Adjusting, Fastening, Magnets
- Antivibration, Soundproofing Materials, Safety Products
- Fasteners
A good selection of accessories such as screws, bolts, washers and nuts that you may need for your daily engineering usage.
- Materials
Browse industrial materials ranging from heat insulating plates, sponges, to metal and plastic materials in different sizes to meet your various applications.
- Wiring Components
A wide variety of wiring parts for connecting and protecting control and PC parts including Connectors, Cables, Electric Wires, Crimping Terminals and more.
- LAN Cables / Industrial Network Cables
- Cables by Application
- Cables with Connectors
- RS232 / Personal Computers / AV Cables
- Wires/Cables
- Connectors (General Purpose)
- Crimp Terminals
- Zip Ties
- Cable Glands
- Cable Bushings/Clips/Stickers
- Screws/Spacers
- Cable Accessories
- Tubes
- Protection Tubes
- Ducts/Wiremolds
- General Purpose Tools
- Dedicated Tools
- Soldering Supplies
- Electrical & Controls
A wide variety of controls and PC parts for electrical engineers including Controls, Powers, PC parts and more.
- Cutting Tools
A wide variety of cutting tools for many uses and work materials including End Mills, Drills, Cutters, Reamers, Turning Tools and more.
- Carbide End Mills
- HSS End Mills
- Milling Cutter Inserts/Holders
- Customized Straight Blade End Mills
- Dedicated Cutters
- Turning Tools
- Drill Bits
- Screw-Hole-Related Tools
- Reamers
- Chamfering / Centering Tools
- Fixtures Related to Cutting Tools
- Step Drills
- Hole Saws
- Clean Key Cutters
- Core Drills (Tip Tools)
- Magnetic Drilling Machine Cutters
- Drill Bits for Electric Drilling Machines
- Woodworking Drill Cutters
- Drills for Concrete
- Processing Tools
A wide variety of tools and supplies used in processing including Machine Tools, Measurement Tools, Grinding and Polishing Supplies and more.
- Material Handling & Storage
A wide variety of goods used in shipment, material handling and warehouse including Tape supplies, Stretch film, Truck, Shelf, Crane and more.
- Tape Supplies
- Cushioning Materials
- Stretch Films
- Cardboard
- Plastic Bags
- PP Bands
- Magic Tapes / Tying Belts
- Rubber Bands
- Strings/Ropes
- Cable Ties
- Tags
- Labelers
- Unpacking Cutters
- Packing Support Equipment
- Cloth Sheets for Packing
- Conveyance/Dolly Carts
- Tool Wagons
- Tool Cabinets / Container Racks
- Lifters / Hand Pallets
- Container Pallets
- Storage Supplies
- Shelves/Racks
- Work Benches
- Suspended Clamps/Suspended Belts
- Jack Winches
- Chain Block Cranes
- Bottles/Containers
- Bicycle Storage Area
- Safety & General Supplies
A large variety of goods for every kind of factories and offices including Protection items, Cleaning supplies, sanitations, office supplies and more.
- Lab & Clean Room Supplies
A large variety of items used in R&D and Clean Room including research Equipment, Laboratory Essentials, Analysis Supplies, Clean Environment-Related Equipment and more.
- Press Die Components
Choose from thousands of standard stamping die components including Punch & Die, Gas Springs, Guide Components, Coil Springs and many more.
- Plastic Mold Components
Browse our wide variety of mold components including Ejector Pins, Sleeves, Leader Components, Sprue Bushings and many more.
- Ejector Pins
- Sleeves, Center Pins
- Core Pins
- Sprue bushings, Gates, and other components
- Date Mark Inserts, Recycle Mark Inserts, Pins with Gas Vent
- Undercut, Plates
- Leader Components, Components for Ejector Space
- Mold Opening Controllers
- Cooling or Heating Components
- Accessories, Others
- Components of Large Mold, Die Casting
- Injection Molding Components
Browse our injection molding components including Heating Items, Couplers, Hoses and more.
- Purging Agent
- Injection Molding Machine Products
- Accessories of Equipment
- Auxiliary Equipment
- Air Nippers
- Air Cylinders
- Air Chuck for Runner
- Chuck Board Components
- Frames
- Suction Components
- Parallel Air Chuck
- Special Air Chuck
- Chemical for Injection Molding
- Mold Maintenance
- Heating Items
- Heat Insulation Sheets
- Couplers, Plugs, One-touch Joints
- Tubes, Hoses, Peripheral Components
Search by Application
Brands
Order / Quote
- Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 9:00 24/11/2024 to 7:00 (MYT) 25/11/2024. We apologize for the inconvenience.
- Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.
- Please note that E-Invoice will be sent to our customers by email. For more information, please read News.
Sprockets Nominal No.35
- Volume Discount
Part Number
Configured Part Number is shown.
Product Overview of Sprockets
■ Sprockets is a solid or spoked gear that engages with a roller chain to transfer motion or power.
Application of Sprockets: It is widely used in mechanical transmission in chemical industry, textile machinery, food processing, instrumentation,and petroleum
■ Only Sprockets and chains of the same specifications can be used in combination.
This series is ISO 06A/ANSI 35 Sprockets, and can be used in combination with MISUMI 35 series chain.
■ Do not use it with ISO/ANSI 06B series chain, which may cause the chain Sprockets mechanism to fail to function properly!
■ Due to process reasons, it is impossible to guarantee the coincidence of the tooth tops of multiple Sprockets. If you need to use the tooth tops in an overlapping manner, please contact us.
Actual Product
Application of Sprockets: It is widely used in mechanical transmission in chemical industry, textile machinery, food processing, instrumentation,and petroleum
■ Only Sprockets and chains of the same specifications can be used in combination.
This series is ISO 06A/ANSI 35 Sprockets, and can be used in combination with MISUMI 35 series chain.
■ Do not use it with ISO/ANSI 06B series chain, which may cause the chain Sprockets mechanism to fail to function properly!
■ Due to process reasons, it is impossible to guarantee the coincidence of the tooth tops of multiple Sprockets. If you need to use the tooth tops in an overlapping manner, please contact us.
Actual Product
Product Feature of Sprockets
■ Sprockets chain drive has the following features compared with gear drive and belt drive:
1. Sprockets, safe and reliable;
2. Sprockets, Flexible transmission, absorbing shock and vibration;
3. Sprockets, Large center distance range, low manufacturing and mounting accuracy requirements;
4. Sprockets, Compared with belt drive, the transmission ratio is accurate and the transmission efficiency is higher, suitable for high temperature，dusty and humid environments.
■ Sprockets, chain selection
Misumi’s Sprockets and chain product selection supports the principle of “Nominal Numbering”
1. Sprockets, safe and reliable;
2. Sprockets, Flexible transmission, absorbing shock and vibration;
3. Sprockets, Large center distance range, low manufacturing and mounting accuracy requirements;
4. Sprockets, Compared with belt drive, the transmission ratio is accurate and the transmission efficiency is higher, suitable for high temperature，dusty and humid environments.
■ Sprockets, chain selection
Misumi’s Sprockets and chain product selection supports the principle of “Nominal Numbering”
Dimensional Drawing of Sprockets
Product Drawings (Unit: mm)
Sprockets processed by shaft hole and keyway. ※ This series is 06C Japanese Standard Sprockets, and can not be used in combination with Chinese Standard 06B series Sprockets.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ The engraving of Sprockets body may be different from the ordered model, please check the engraving number.
※ This series is 06C Japanese Standard Sprockets, and can not be used in combination with Chinese Standard 06B series Sprockets.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ The engraving of Sprockets body may be different from the ordered model, please check the engraving number.
Sprockets processed by shaft hole and keyway. ※ This series is 06C Japanese Standard Sprockets, and can not be used in combination with Chinese Standard 06B series Sprockets.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ The engraving of Sprockets body may be different from the ordered model, please check the engraving number.
| Type |  Material |  Surface Treatment |  Accessories |
| C-SP35B | Equivalent to S45C (Induction Hardened Teeth Tip) | － | Fixing Screw (Only Shaft Hole Specifications N) |
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ The engraving of Sprockets body may be different from the ordered model, please check the engraving number.
Usage Method of Sprockets
Example Use of Sprockets
Precautions of Sprockets
■ Sprockets maintenance
1. Sprockets tightness should be suitable. If it is too tight, it will increase power consumption, and bearing is easy to wear; if it is too loose, the Sprockets is easy to runout and fall off the chain.
The degree of tightness of the Sprockets is: if lifted up or pressed down from the middle of the Sprockets, the center distance between the two Sprockets is about 2%-3%.
2. The Sprockets shall be installed on shaft without swing and skew.
The end faces of the two Sprockets in the same transmission assembly should be in the same plane. When the center distance of the Sprockets is less than 0.5 meters, the deviation can be 1 mm.
When the center distance of the Sprockets is more than 0.5 meters, the deviation can be 2 mm. But there shall be no friction on Sprockets tooth side. Integral offset.
If the offset is too large, chain is prone to fall off and wear is likely to accelerate. When replacing the Sprockets, you must pay attention to check and adjust the offset
3. After the Sprockets is severely worn, the new Sprockets and the new chain should be replaced at the same time to ensure good meshing.
You cannot replace new Sprockets separately. Otherwise, it will cause bad engagement and accelerate the wear of new Sprockets.
If the tooth surface of the Sprockets is worn to a certain degree, it should be turned over in time (the Sprockets used with adjustable surface) to extend the life time.
4. If the new Sprockets is too long or elongated after use, and difficult to adjust, the links can be removed by the case, but the number of the links must be even.
The link should pass through the back of the Sprockets with the lock piece being inserted outside, and the opening of the lock piece should be in the opposite direction of the turning.
5. Lubricating oil should be timely filled when Sprockets are working. Lubricating oil must enter the matching clearance between the roller and the inner sleeve to improve working conditions and reduce wear.
6. The old Sprockets cannot be mixed with some of the new Sprockets, and should be replaced as a complete set, otherwise it is easy to produce impact in the transmission. Separate replacement of Sprockets will increase wear.
1. Sprockets tightness should be suitable. If it is too tight, it will increase power consumption, and bearing is easy to wear; if it is too loose, the Sprockets is easy to runout and fall off the chain.
The degree of tightness of the Sprockets is: if lifted up or pressed down from the middle of the Sprockets, the center distance between the two Sprockets is about 2%-3%.
2. The Sprockets shall be installed on shaft without swing and skew.
The end faces of the two Sprockets in the same transmission assembly should be in the same plane. When the center distance of the Sprockets is less than 0.5 meters, the deviation can be 1 mm.
When the center distance of the Sprockets is more than 0.5 meters, the deviation can be 2 mm. But there shall be no friction on Sprockets tooth side. Integral offset.
If the offset is too large, chain is prone to fall off and wear is likely to accelerate. When replacing the Sprockets, you must pay attention to check and adjust the offset
3. After the Sprockets is severely worn, the new Sprockets and the new chain should be replaced at the same time to ensure good meshing.
You cannot replace new Sprockets separately. Otherwise, it will cause bad engagement and accelerate the wear of new Sprockets.
If the tooth surface of the Sprockets is worn to a certain degree, it should be turned over in time (the Sprockets used with adjustable surface) to extend the life time.
4. If the new Sprockets is too long or elongated after use, and difficult to adjust, the links can be removed by the case, but the number of the links must be even.
The link should pass through the back of the Sprockets with the lock piece being inserted outside, and the opening of the lock piece should be in the opposite direction of the turning.
5. Lubricating oil should be timely filled when Sprockets are working. Lubricating oil must enter the matching clearance between the roller and the inner sleeve to improve working conditions and reduce wear.
6. The old Sprockets cannot be mixed with some of the new Sprockets, and should be replaced as a complete set, otherwise it is easy to produce impact in the transmission. Separate replacement of Sprockets will increase wear.
Specification Table of Sprockets
Please order after selecting part number and parameters according to the selection steps 
to 
.
Fixing Screw of Symbol ＊ is M6.
If 10K is selected, the shaft hole diameter is φ10 and the keyway width is 4mm (height 1.8mm).
Symbol indicates that there is a notch on the outer diameter of the hub.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ Shaft Hole Machining Size Table
to 
.Part Number (Type· No. of Teeth) | － |  Specifications | － | Shaft Hole Diameter | |
| Sprockets | C-SPA35B20 | － | N | － | 20 |
| Part Number | Shaft Hole Specifications | Shaft Hole Diameter (D) | Dp | D0 | H | GD | L | ℓ | |||||||||||||||
| Type | Nominal model | Hub type | Number of Teeth | S Specifications | N Specifications (H7) | ||||||||||||||||||
| C－SPA | 35 | B | 9 | S N | 8 | 10 | 27.85 | 32 | 21.5 | 17 | 20 | 6 | |||||||||||
| 10 | 8 | 10 | 12 | 30.82 | 34 | 24.5 | 20 | ||||||||||||||||
| 11 | 8 | 12 | 33.81 | 38 | 27 | 23 | |||||||||||||||||
| 12 | 9 | 10 | 12 | 14 | 15 | 16 | 17 | 36.8 | 41 | 30.5 | 26 | ||||||||||||
| 13 | 9 | 12 | 15 | 39.8 | 44 | 32 | 29 | ||||||||||||||||
| 14 | 9 | 12 | 14 | 15 | 17 | 42.81 | 47 | 32 | - | ||||||||||||||
| 15 | 9 | 10 | 12 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 45.81 | 51 | 35 | ||||||||||
| 16 | 9 | 12 | 15 | 18 | 20 | 48.82 | 54 | 37 | |||||||||||||||
| 17 | 11 | 15 | 20 | 51.84 | 57 | 41 | |||||||||||||||||
| 18 | 11 | 15 | 54.85 | 60 | 44 | ||||||||||||||||||
| 20 | 11 | 12 | 15 | 16 | 20 | 25 | 60.89 | 66 | 50 | ||||||||||||||
| 21 | 11 | 28 | 63.91 | 69 | 53 | ||||||||||||||||||
| 22 | 11 | 12 | 66.93 | 72 | 56 | ||||||||||||||||||
| 24 | 11 | 15 | 72.97 | 78 | 53 | 22 | 8 | ||||||||||||||||
| 32 | 11 | 15 | 97.18 | 102 | |||||||||||||||||||
Fixing Screw of Symbol ＊ is M6.If 10K is selected, the shaft hole diameter is φ10 and the keyway width is 4mm (height 1.8mm). Symbol indicates that there is a notch on the outer diameter of the hub.■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ Shaft Hole Machining Size Table
| Shaft Hole Diameter D | Keyway b2×t2 | Fixing Screw M |
| 10 | 3×1.4 | 4 |
| 10K··12 | 4×1.8 | 5 |
| 14~17 | 5×2.3 | 6 |
| 18~22 | 6×2.8 | 6 |
| 24~30 | 8×3.3 | 8 |
Specification Table
Please order after selecting part number and parameters according to the selection steps 
to 
.
Fixing Screw of Symbol ＊ is M6.
If 10K is selected, the shaft hole diameter is φ10 and the keyway width is 4mm (height 1.8mm).
Symbol indicates that there is a notch on the outer diameter of the hub.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ Shaft Hole Machining Size Table
to 
.Part Number (Type· No. of Teeth) | － |  Specifications | － | Shaft Hole Diameter | |
| Sprocket | C-SPA35B20 | － | N | － | 20 |
| Part Number | Shaft Hole Specifications | Shaft Hole Diameter (D) | Dp | D0 | H | GD | L | ℓ | |||||||||||||||
| Type | Nominal model | Hub type | Number of Teeth | S Specifications | N Specifications (H7) | ||||||||||||||||||
| C－SPA | 35 | B | 9 | S N | 8 | 10 | 27.85 | 32 | 21.5 | 17 | 20 | 6 | |||||||||||
| 10 | 8 | 10 | 12 | 30.82 | 34 | 24.5 | 20 | ||||||||||||||||
| 11 | 8 | 12 | 33.81 | 38 | 27 | 23 | |||||||||||||||||
| 12 | 9 | 10 | 12 | 14 | 15 | 16 | 17 | 36.8 | 41 | 30.5 | 26 | ||||||||||||
| 13 | 9 | 12 | 15 | 39.8 | 44 | 32 | 29 | ||||||||||||||||
| 14 | 9 | 12 | 14 | 15 | 17 | 42.81 | 47 | 32 | - | ||||||||||||||
| 15 | 9 | 10 | 12 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 45.81 | 51 | 35 | ||||||||||
| 16 | 9 | 12 | 15 | 18 | 20 | 48.82 | 54 | 37 | |||||||||||||||
| 17 | 11 | 15 | 20 | 51.84 | 57 | 41 | |||||||||||||||||
| 18 | 11 | 15 | 54.85 | 60 | 44 | ||||||||||||||||||
| 20 | 11 | 12 | 15 | 16 | 20 | 25 | 60.89 | 66 | 50 | ||||||||||||||
| 21 | 11 | 28 | 63.91 | 69 | 53 | ||||||||||||||||||
| 22 | 11 | 12 | 66.93 | 72 | 56 | ||||||||||||||||||
| 24 | 11 | 15 | 72.97 | 78 | 53 | 22 | 8 | ||||||||||||||||
| 32 | 11 | 15 | 97.18 | 102 | |||||||||||||||||||
Fixing Screw of Symbol ＊ is M6.If 10K is selected, the shaft hole diameter is φ10 and the keyway width is 4mm (height 1.8mm). Symbol indicates that there is a notch on the outer diameter of the hub.■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ Shaft Hole Machining Size Table
| Shaft Hole Diameter D | Keyway b2×t2 | Fixing Screw M |
| 10 | 3×1.4 | 4 |
| 10K··12 | 4×1.8 | 5 |
| 14~17 | 5×2.3 | 6 |
| 18~22 | 6×2.8 | 6 |
| 24~30 | 8×3.3 | 8 |
Part Number
CAD Data download and 3D preview are not available because the part number has not yet been determined.
- *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
- Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
Loading...
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Number of Teeth (T) | Shaft Bore Dia. D (or d) (mm) | Number of Strands | Chain Type | Type | Shaft Type | Bore Specification |
|---|---|---|---|---|---|---|---|---|---|---|---|
MYR 16.37 | 2 Piece(s) | 11 Day(s) | 10 | 10 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 16.39 | 1 Piece(s) | 1 Day(s) | 10 | 12 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 19.04 | 1 Piece(s) | 5 Day(s) | 12 | 10 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 19.06 | 1 Piece(s) | 1 Day(s) | 12 | 15 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 20.73 | 1 Piece(s) | 1 Day(s) | 13 | 15 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 21.41 | 1 Piece(s) | 1 Day(s) | 14 | 12 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 21.41 | 1 Piece(s) | 1 Day(s) | 14 | 15 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 21.86 | 2 Piece(s) | 11 Day(s) | 15 | 12 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 21.86 | 2 Piece(s) | 11 Day(s) | 15 | 15 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 21.88 | 2 Piece(s) | 5 Day(s) | 15 | 17 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 21.88 | 2 Piece(s) | 11 Day(s) | 15 | 20 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 27.01 | 1 Piece(s) | 1 Day(s) | 17 | 20 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) | ||
MYR 27.44 | 2 Piece(s) | 5 Day(s) | 18 | 15 | [1] 1 | RS | Shaft Bore Machined Type | Shaft Bore Machining Configurable | N (New JIS Key + Screw Bore Type) |
Loading...
Basic Information
| Sprocket Shape | Shape B | Nominal | 35 | Material | S45C |
|---|---|---|---|---|---|
| Surface Treatment | Not Provided |
Specification/Dimensions
-
Number of Teeth(T)
-
Shaft Bore Dia. D (or d)(mm)
-
Number of Strands
- 1
- 1
-
Chain Type
- RS
-
Shaft Type
- Standard Pilot Bore
- Shaft Bore Machining Configurable
-
Bore Specification
- N (New JIS Key + Screw Bore Type)
- S (Through Hole)
-
type
- C-SPA35B
-
Type
- Pilot Bore Type
- Shaft Bore Machined Type
-
CAD
- 2D
- 3D
Days to Ship
-
- All
- 1 Day(s) or Less
- 5 Day(s) or Less
- 11 Day(s) or Less
- 18 Day(s) or Less
Specify Alterations
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Frequently asked question (FAQ)
- Question: I bought MISUMI chains, but why can't I use them on my original sprocket?
- Answer: Please confirm the specifications of the original sprocket and chain. Specification series number may not match. In addition, there are two specifications: A series and B series in China. The two specifications of sprocket chain are not universal.
- Question: Does the sprocket need routine maintenance after installation and use?
- Answer: The chain needs regular maintenance after installation and use. These include daily lubricant application, confirmation of chain slack. After the sprocket is severely worn, the new sprocket and the new chain should be replaced at the same time to ensure good meshing.
- Question: I need to use two overlapped sprockets, I want the tooth top direction to be consistent, is it possible?
- Answer: Due to process reasons, it is impossible to guarantee the overlapping of the tooth tops of several sprockets. If the tooth tops are required to be overlapped, please contact our company or indicate on the order (the tooth tops need to be overlapped)
- Question: The engraving on the sprocket does not match the packaged model, is it shipped wrongly?
- Answer: The product model is subject to the label on the shipping bag and the actual size. The engraving is only the factory management number of the sprocket product during processing, and is not directly associated with the product model.
Additional Products in this Category
Tech Support
- Credit Card
- Bank Transfer
Social Media
MISUMI Contact
Copyright © MISUMI Corporation All Rights Reserved.
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy