(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.

7 Million Products, 2,000 Brands.
50,000 Stock items for Same Day Ship Out.
Tel: (60) 3 7890 6399
9am – 6pm (Mon – Fri), 9am – 1pm (Sat)

All Categories

Categories

Search by Application

Brands

  • MISUMI Economy Series
  • Mold EX Press
Webcode Seach | Series
#CODE
Keyword suggestions
Part number suggestions
Discontinued Products
Order / Quote

Part Number Checker

  • Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 9:00 24/11/2024 to 7:00 (MYT) 25/11/2024. We apologize for the inconvenience.
  • Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.　
  • Please note that E-Invoice will be sent to our customers by email. For more information, please read News.　

  • How can we improve?

    How can we improve?

    Comments
    Name (Optional)
    E-mail Address (Optional)
    Tel (Optional)

    While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
    Customer Privacy Policy

    Thank you for your cooperation.

    While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
    Please use the inquiry form.

    Customer Privacy Policy

Sprockets Nominal No.80

Sprockets Nominal No.80
  • Volume Discount
Check FAQ of this product (4 items)

MISUMI

MiSUMi Economy

MISUMI

Part Number

Configured Part Number is shown.

Actual Product of Sprockets

Sprockets

Product Overview of Sprockets

■ Sprockets is a solid or spoked gear that engages with a roller chain to transfer motion or power.
Application of sprocket: It is widely used in mechanical transmission in chemical industry, textile machinery, food processing, instrumentation,and petroleum

■ Only Sprockets and chains of the same specifications can be used in combination.
This series is ISO 16A/ANSI 80 sprocket, and can be used in combination with MISUMI 80 series chain.
■ Do not use it with ISO/ANSI 16B series chain, which may cause the chain Sprockets mechanism to fail to function properly!

■ Due to process reasons, it is impossible to guarantee the coincidence of the tooth tops of multiple Sprockets. If you need to use the tooth tops in an overlapping manner, please contact us.

Product Feature of Sprockets

■ Compared with gear drive and belt drive, Sprockets chain drive has the following characteristics:
1. Multi-tooth load-bearing, safe and reliable;
2. Flexible transmission, absorbing shock and vibration;
3. Large center distance range, low manufacturing and installation accuracy requirements;
4. Compared with belt transmission, the transmission ratio is more accurate and the transmission efficiency is higher. The Sprockets is suitable for the harsh environment of high temperature, dust and humidity.

■ Sprockets, chain selection
Misumi’s Sprockets and chain product selection supports the principle of “Nominal Numbering”
Product Feature

Dimensional Drawing of Sprockets

Product Drawings of Sprockets (Unit: mm)
Sprocket 80B: related images
 
Sprockets TypeSprockets Sprockets MaterialSprockets Accessories
C-SPA80BEquivalent to S45C
(Induction Hardened Teeth Tip)		Fixing Screw
(Only Shaft Hole Specifications N)
This series is 16A Japanese Standard Sprockets, and can not be used in combination with Chinese Standard 16B series sprocket.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!
■ The engraving of Sprockets body may be different from the ordered model, please check the engraving number.
Sprockets＊ Fixing Screw of Symbol ＊ is M6.
Sprockets＊＊ Symbol indicates that there is a notch on the outer diameter of the hub.
■ A single package label may not match the ordered model. The Sprockets is a factory-managed model. Please note that the outer package label shall prevail!

Usage Method of Sprockets

How to mount the roller Sprockets
(A) Axis configuration
■Sprockets Horizontal
Even when the two axes are arranged horizontally, the rotation direction of the axis must be considered.
The examples (2) and (3) in the figure show that when the chain is stretched, the disengagement between the Sprockets teeth and the chain is not smooth and may bite.
In particular, the upper and lower chains in (3) will contact each other, so an idler is required.		Usage Method 1
 
■Sprockets Vertical
If the chain is stretched, slack as shown in (5) will occur, and
when a small sprocket is used on the lower side, the chain may fall off. Therefore, please use it at an angle of 60 or less as shown in (4).
When it is necessary to use it vertically due to the mechanism or space, it is recommended to put the large Sprockets on the lower side, and use the idler on the outside or inside as shown in (6).		Usage Method 2
 
(B) Deflection
Deflection is generally about 4% of the shaft spacing, and about 2% in the following cases.
a. The Sprockets Vertical transmission or close to vertical transmission
b. Shaft spacing is more than 1m
c. When frequent heavy load starting and stopping are required
d. When reverse rotation is required		Usage Method 3
 
(C) When the load changes Sprockets
If a tension adjuster is mounted on the tension side or slack side of the chain to provide initial tension in advance, it will eliminate vibration and reduce noise during operation.		Usage Method 4

Example Use of Sprockets

The Sprockets Used for driving power
A mechanism that can convert motor power into roller rotation by combining multiple Sprockets and chains		Example of Use 1
 
The Sprockets Used for transporting workpieces
A chain conveyor frame with high versatility using flat profiles and chain guides		Example of Use 2
 
The Sprockets Used for transporting workpieces
A mechanism used to mount accessories on the chain, and extract and transport workpieces		Example of Use 3

Precautions of Sprockets

■ Sprockets maintenance
1. Sprockets tightness should be suitable. If it is too tight, it will increase power consumption, and bearing is easy to wear; if it is too loose, the sprocket is easy to runout and fall off the chain.
 The degree of tightness of the sprocket is: if lifted up or pressed down from the middle of the sprocket, the center distance between the two sprocket is about 2%-3%.

2. The Sprockets shall be installed on shaft without swing and skew.
 The end faces of the two Sprockets in the same transmission assembly should be in the same plane. When the center distance of the sprocket is less than 0.5 meters, the deviation can be 1 mm.
  When the center distance of the sprocket is more than 0.5 meters, the deviation can be 2 mm. But there shall be no friction on sprocket tooth side. Integral offset.
 If the offset is too large, chain is prone to fall off and wear is likely to accelerate. When replacing the sprocket, you must pay attention to check and adjust the offset

3. After the Sprockets is severely worn, the new sprocket and the new chain should be replaced at the same time to ensure good meshing.
 You cannot replace new Sprockets separately. Otherwise, it will cause bad engagement and accelerate the wear of new Sprockets.
 If the tooth surface of the sprocket is worn to a certain degree, it should be turned over in time (the sprocket used with adjustable surface) to extend the life time.

4. If the new Sprockets is too long or elongated after use, and difficult to adjust, the links can be removed by the case, but the number of the links must be even.
 The link should pass through the back of the sprocket with the lock piece being inserted outside, and the opening of the lock piece should be in the opposite direction of the turning.

5. Lubricating oil should be timely filled when Sprockets are working. Lubricating oil must enter the matching clearance between the roller and the inner sleeve to improve working conditions and reduce wear.

6. The old Sprockets cannot be mixed with some of the new sprocket, and should be replaced as a complete set, otherwise it is easy to produce impact in the transmission. Separate replacement of Sprockets will increase wear.

Specification Table of Sprockets

 Part Number (SprocketsSprockets Type·Sprockets No. of Teeth)－SprocketsSpecifications－SprocketsShaft Hole Diameter
SprocketsC-SPA80B15－N－40
 
Part Number of SprocketsSprocketsShaft Hole SpecificationsSprocketsShaft Hole Diameter (D)DpD0HLℓ
SprocketsSprockets TypeSprockets Nominal modelHub typeSprocketsNumber of TeethS SpecificationsN Specifications (H7)
C－SPA80B12S
N		15  40 98.14110674012
141625   114.1512777
1520   50122.1713593
162025   130.2143
1720   50138.23151
2020 35  162.37176
Symbol ＊ indicates that there is a notch on the outer diameter of the hub.
■ A single package label may not match the ordered model of Sprockets. It is a factory-managed model. Please note that the outer package label shall prevail!

■ Sprockets, Shaft Hole Machining Size Table
Shaft Hole Diameter DKeyway b2×t2Fixing Screw M
25~308×3.38
32~3810×3.38
40·4212×3.38
45·5014×3.810

Specification Table
 Part Number (Type· No. of Teeth)－Specifications－Shaft Hole Diameter
SprocketC-SPA80B15－N－40
 
Part NumberShaft Hole SpecificationsShaft Hole Diameter (D)DpD0HLℓ
TypeNominal modelHub typeNumber of TeethS SpecificationsN Specifications (H7)
C－SPA80B12S
N		15  40 98.14110674012
141625   114.1512777
1520   50122.1713593
162025   130.2143
1720   50138.23151
2020 35  162.37176
Symbol ＊ indicates that there is a notch on the outer diameter of the hub.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!

■ Shaft Hole Machining Size Table
Shaft Hole Diameter DKeyway b2×t2Fixing Screw M
25~308×3.38
32~3810×3.38
40·4212×3.38
45·5014×3.810

Part Number 

CAD Data download and 3D preview are not available because the part number has not yet been determined.

  • *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
  • Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
Loading...

CAD Download

30
45
60
  1. 1
Part Number
C-SPA80B12-N-40
C-SPA80B12-S-15
Part NumberStandard Unit PriceMinimum order quantityVolume DiscountDays to ShipShaft Bore Dia. D (or d)
(mm) 		Type Shaft Type Bore Specification

MYR 92.84

2 Piece(s) 18 Day(s) 40Shaft Bore Machined TypeShaft Bore Machining ConfigurableN (New JIS Key + Screw Bore Type)

MYR 169.06

2 Piece(s)Available 17 Day(s) 15Pilot Bore TypeStandard Pilot BoreS (Through Hole)

Loading...

  1. 1

Basic Information

Sprocket Shape Shape B Nominal 80 Number of Teeth(T) 12
Number of Strands 1 Material S45C Chain Type RS
Surface Treatment Not Provided

Configure

Clear All

2 Part Numbers

View Part Numbers

Configure Remaining Specifications
Completed
loading

Specification/Dimensions

  • Shaft Bore Dia. D (or d)(mm)

    • 15
    • 40

    Clear

  • Type

    • Pilot Bore Type
    • Shaft Bore Machined Type

    Clear

  • Shaft Type

    • Standard Pilot Bore
    • Shaft Bore Machining Configurable

    Clear

  • Bore Specification

    • N (New JIS Key + Screw Bore Type)
    • S (Through Hole)

    Clear

  • type

    • C-SPA80B

    Clear

  • CAD

    • 2D
    • 3D

    Clear

Days to Ship

    • All
    • 17 Day(s) or Less
    • 18 Day(s) or Less

    Clear

Specify Alterations

Frequently asked question (FAQ)

Question: I bought MISUMI chains, but why can't I use them on my original sprocket?
Answer: Please confirm the specifications of the original sprocket and chain. Specification series number may not match. In addition, there are two specifications: A series and B series in China. The two specifications of sprocket chain are not universal.
Question: Does the sprocket need routine maintenance after installation and use?
Answer: The chain needs regular maintenance after installation and use. These include daily lubricant application, confirmation of chain slack. After the sprocket is severely worn, the new sprocket and the new chain should be replaced at the same time to ensure good meshing.
Question: I need to use two overlapped sprockets, I want the tooth top direction to be consistent, is it possible?
Answer: Due to process reasons, it is impossible to guarantee the overlapping of the tooth tops of several sprockets. If the tooth tops are required to be overlapped, please contact our company or indicate on the order (the tooth tops need to be overlapped)
Question: The engraving on the sprocket does not match the packaged model, is it shipped wrongly?
Answer: The product model is subject to the label on the shipping bag and the actual size. The engraving is only the factory management number of the sprocket product during processing, and is not directly associated with the product model.

Check other FAQ (1 items) Hide

Additional Products in this Category

Tech Support

Technical Inquiry

Payment Method

more
  • Credit Card
    • VISA
    • MasterCard
  • Bank Transfer
    • FPX
    • Interbank GIRO (IBG)

About MISUMI

About this Website

Useful Tools

Customer Service

Social Media

MISUMI Contact 9am – 6pm (Mon – Fri) * Order cut-off time is 5pm,    9am – 1pm(Sat) * Order cut-off time is 12pm

  • Tel: (60) 3 7890 6399
Inquiry
Mobile View

Copyright © MISUMI Corporation All Rights Reserved.