(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.

7 Million Products, 2,000 Brands.
50,000 Stock items for Same Day Ship Out.

Tel: (60) 3 7890 6399

9am – 6pm (Mon – Fri), 9am – 1pm (Sat)

All Categories

Search by Application

inCAD Library

Brands

Webcode Seach | Series: #CODE

Keyword suggestions

Part number suggestions

Discontinued Products

Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 9:00 24/11/2024 to 7:00 (MYT) 25/11/2024. We apologize for the inconvenience.
Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.　
Please note that E-Invoice will be sent to our customers by email. For more information, please read News.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

[Short Delivery Size] Full-Ball Type LM Guide, International Standard, HSR Type (Part Numbers)

THK

A best selling THK product. The HSR series can be used in any position.
*When ordering multiple shaft types, input multiples of the number of required shafts as the order quantity.
(Example) required shafts: 2(-II)⇒ Order quantity: "2, 4, 6..."
Required shafts: 3 3(-III)⇒ Order quantity: "3, 6, 9..."
Please place your orders in this manner.

Part Number

Configured Part Number is shown.

Product Specifications
Part Numbers
Catalog

INDEX

Drawing

How to use and use cases

Product comparison information

Basic specifications and features of the product

Cautions/prohibitions

Drawing

HSR-A type, HSR-LA type

Drawing / Standard table

HSR-A type
A type where tapping has been performed on the flange part of the LM block.

HSR-LA type
It is a type with the same cross-sectional shape as the HSR-A type, with a longer LM block overall length (L) and an increased rated load.

Drawing 1 of HSR-A type and HSR-LA type

Drawing 2 of HSR-A type and HSR-LA type

(Unit: mm)

Nominal model number	External dimensions			LM block dimensions								H₃	LM rail dimensions
Nominal model number	Height M	Width W	Length L	B	C	S	L₁	T	K	N	E	H₃	Width W₁ ±0.05	W₂	Height M1	Pitch F	d1 × d2 × h
HSR 15 A	24	47	56.6	38	30	M5	38.8	7	19.3	4.3	5.5	4.7	15	16	15	60	4.5 × 7.5 × 5.3
HSR 20 A	30	63	74	53	40	M6	50.8	9.5	26	5	12	4	20	21.5	18	60	6 × 9.5 × 8.5
HSR 20LA	30	63	90	53	40	M6	66.8	9.5	26	5	12	4	20	21.5	18	60	6 × 9.5 × 8.5
HSR 25 A	36	70	83.1	57	45	M8	59.5	11	30.5	6	12	5.5	23	23.5	22	60	7 × 11 × 9
HSR 25LA	36	70	102.2	57	45	M8	78.6	11	30.5	6	12	5.5	23	23.5	22	60	7 × 11 × 9
HSR 30 A	42	90	98	72	52	M10	70.4	9	35	7	12	7	28	31	26	80	9 × 14 × 12
HSR 30LA	42	90	120.6	72	52	M10	93	9	35	7	12	7	28	31	26	80	9 × 14 × 12
HSR 35 A	48	100	109.4	82	62	M10	80.4	12	40.5	8	12	7.5	34	33	29	80	9 × 14 × 12
HSR 35LA	48	100	134.8	82	62	M10	105.8	12	40.5	8	12	7.5	34	33	29	80	9 × 14 × 12

Configuration example of nominal model number

*) This nominal model number is 1 set for a 1-axis unit. (The required number for 2-axis parallel use is at least 2 sets.)
If the lubricator QZ is attached, the grease fitting is not attached.

HSR-B type, HSR-LB type

Drawing / Standard table

HSR-B type
Since through holes are machined on the flange of the LM block, they are used when there is no through hole for mounting bolts on the table.

HSR-LB type
It is a type with the same cross-sectional shape as the HSR-B type, with a longer LM block overall length (L) and an increased rated load.

Drawing 1 of HSR-B type and HSR-LB type

Drawing 2 of HSR-B type and HSR-LB type

(Unit: mm)

Nominal model number	External dimensions			LM block dimensions							H₃	LM rail dimensions
	Height M	Width W	Length L	B	C	L₁	T	K	N	E		Width W₁ ±0.05	W₂	Height M1	Pitch F	d1 × d2 × h
	Height M	Width W	Length L	B	C	L₁	T	K	N	E		Width W₁ ±0.05	W₂	Height M1	Pitch F	d1 × d2 × h
HSR 15B	24	47	56.6	38	30	38.8	7	19.3	4.3	5.5	4.7	15	16	15	60	4.5 × 7.5 × 5.3
HSR 20B	30	63	74	53	40	50.8	9.5	26	5	12	4	20	21.5	18	60	6 × 9.5 × 8.5
HSR 20LB	30	63	90	53	40	66.8	9.5	26	5	12	4	20	21.5	18	60	6 × 9.5 × 8.5
HSR 25B	36	70	83.1	57	45	59.5	11	30.5	6	12	5.5	23	23.5	22	60	7 × 11 × 9
HSR 25LB	36	70	102.2	57	45	78.6	11	30.5	6	12	5.5	23	23.5	22	60	7 × 11 × 9
HSR 30B	42	90	98	72	52	70.4	9	35	7	12	7	28	31	26	80	9 × 14 × 12
HSR 30LB	42	90	120.6	72	52	93	9	35	7	12	7	28	31	26	80	9 × 14 × 12
HSR 35B	48	100	109.4	82	62	80.4	12	40.5	8	12	7.5	34	33	29	80	9 × 14 × 12
HSR 35LB	48	100	134.8	82	62	105.8	12	40.5	8	12	7.5	34	33	29	80	9 × 14 × 12

Configuration example of nominal model number

*) This nominal model number is 1 set for a 1-axis unit. (The required number for 2-axis parallel use is at least 2 sets.)
If the lubricator QZ is attached, the grease fitting is not attached.

HSR-R type, HSR-LR type

HSR-R type
The LM block width (W) is narrowed and tapped, making it ideal for compact designs.

HSR-LR type
It is a type with the same cross-sectional shape as the HSR-R type, with a longer LM block overall length (L) and an increased rated load.

Drawing 1 of HSR-R type and HSR-LR type

Drawing 2 of HSR-R type and HSR-LR type

(Unit: mm)

Nominal model number	External dimensions			LM block dimensions								H₃	LM rail dimensions
	Height M	Width W	Length L	B	C	S × l	L₁	T	K	N	E		Width W₁ ±0.05	W₂	Height M1	Pitch F	d1 × d2 × h
	Height M	Width W	Length L	B	C	S × l	L₁	T	K	N	E		Width W₁ ±0.05	W₂	Height M1	Pitch F	d1 × d2 × h
HSR 15R	28	34	56.6	26	26	M4 × 5	38.8	6	23.3	8.3	5.5	4.7	15	9.5	15	60	4.5 × 7.5 × 5.3
HSR 20R	30	44	74	32	36	M5 × 6	50.8	8	26	5	12	4	20	12	18	60	6 × 9.5 × 8.5
HSR 20LR	30	44	90	32	50	M5 × 6	66.8	8	26	5	12	4	20	12	18	60	6 × 9.5 × 8.5
HSR 25R	40	48	83.1	35	35	M6 × 8	59.5	9	34.5	10	12	5.5	23	12.5	22	60	7 × 11 × 9
HSR 25LR	40	48	102.2	35	50	M6 × 8	78.6	9	34.5	10	12	5.5	23	12.5	22	60	7 × 11 × 9
HSR 30R	45	60	98	40	40	M8 × 10	70.4	9	38	10	12	7	28	16	26	80	9 × 14 × 12
HSR 30LR	45	60	120.6	40	60	M8 × 10	93	9	38	10	12	7	28	16	26	80	9 × 14 × 12
HSR 35R	55	70	109.4	50	50	M8 × 12	80.4	11.7	47.5	15	12	7.5	34	18	29	80	9 × 14 × 12
HSR 35LR	55	70	134.8	50	72	M8 × 12	105.8	11.7	47.5	15	12	7.5	34	18	29	80	9 × 14 × 12

Configuration example of nominal model number

*) This nominal model number is 1 set for a 1-axis unit. (The required number for 2-axis parallel use is at least 2 sets.)
If the lubricator QZ is attached, the grease fitting is not attached.

HSR-C type, HSR-LC type

HSR-C type
The flange of the LM block is tapped.
It can be installed from either the top or the bottom.
It is used when the table cannot be drilled with through holes for mounting bolts.

HSR-LC type
It is a type with the same cross-sectional shape as the HSR-C type, with a longer LM block overall length (L) and an increased rated load.

Drawing 1 of HSR-C type and HSR-LC type

Drawing 2 of HSR-C type and HSR-LC type

(Unit: mm)

Nominal model number	External dimensions			LM block dimensions								H₃	LM rail dimensions
	Height M	Width W	Length L	B	C	S	L₁	T	K	N	E		Width W₁ ±0.05	W₂	Height M1	Pitch F	d1 × d2 × h
	Height M	Width W	Length L	B	C	S	L₁	T	K	N	E		Width W₁ ±0.05	W₂	Height M1	Pitch F	d1 × d2 × h
HSR 15C	24	47	56.6	38	30	M5	38.8	7	19.3	4.3	5.5	4.7	15	16	15	60	4.5 × 7.5 × 5.3
HSR 15LC	24	47	74.6	38	30	M5	56.8	7	19.3	4.3	5.5	4.7	15	16	15	60	4.5 × 7.5 × 5.3
HSR 20C	30	63	74	53	40	M6	50.8	9.5	26	5	12	4	20	21.5	18	60	6 × 9.5 × 8.5
HSR 20LC	30	63	90	53	40	M6	66.8	9.5	26	5	12	4	20	21.5	18	60	6 × 9.5 × 8.5
HSR 25C	36	70	83.1	57	45	M8	59.5	11	30.5	6	12	5.5	23	23.5	22	60	7 × 11 × 9
HSR 25LC	36	70	102.2	57	45	M8	78.6	11	30.5	6	12	5.5	23	23.5	22	60	7 × 11 × 9
HSR 30C	42	90	98	72	52	M10	70.4	9	35	7	12	7	28	31	26	80	9 × 14 × 12
HSR 30LC	42	90	120.6	72	52	M10	93	9	35	7	12	7	28	31	26	80	9 × 14 × 12
HSR 35C	48	100	109.4	82	62	M10	80.4	12	40.5	8	12	7.5	34	33	29	80	9 × 14 × 12
HSR 35LC	48	100	134.8	82	62	M10	105.8	12	40.5	8	12	7.5	34	33	29	80	9 × 14 × 12

Configuration example of nominal model number

Configuration example of nominal model number

*) This nominal model number is 1 set for a 1-axis unit. (The required number for 2-axis parallel use is at least 2 sets.)
If the lubricator QZ is attached, the grease fitting is not attached.

Basic specifications and features of the product

Structure and features

The balls roll on the 4 rows of rolling surfaces that have been precision ground on the LM rail and LM block, and the end plates incorporated in the LM block circulate the ball rows.
Even if the LM rail is pulled out, balls are held at the holding plate and will not fall off (except for HSR 8, 10 and 12 types).
Since each ball row is arranged at a contact angle of 45° so that the load is the same for the 4 directions (radial direction, reverse radial direction, lateral direction) acting on the LM block, it can be used in any posture. Moreover, since a well-balanced preload is applied, it is possible to increase the stiffness in 4 directions while maintaining a constant low coefficient of friction. It has a low cross-section height, and the LM block has been designed with a high stiffness, which allows for highly precise and consistent linear motion.

4 directions equal load

Since each ball row is arranged at a contact angle of 45° so that the same rated load is applied to the 4 directions (radial direction, reverse radial direction, lateral direction) acting on the LM block, it can be used in any posture and it can be used for a wide range of purposes.

High stiffness type

Since it is a well-balanced 4-row array, sufficient preload is given, and the stiffness in 4 directions can be increased without difficulty.

Automatic adjustment ability

Due to the effect of the automatic adjustment ability by THK's unique front combination of circular arc grooves (DF set), mounting errors can be absorbed even if preload is applied, and high-precision and smooth linear motion can be obtained.

Superior durability

There is no differential slip of the ball even with preload or eccentric load, smooth operation is obtained, and it has excellent abrasion resistance, so accuracy is maintained for a long period of time.

Also available in stainless steel

LM block, LM rail, and LM rail are all compatible with stainless steel.

External appearance of LM guide

Drawing of LM guide

How to use and use cases

Installation procedure and maintenance

Installation of LM guide

Reference Side LM Guide Display and Combination

Fig. 1 Reference side and driven side LM guides (Example: HSR-B type)

[Display of Reference Side LM Guide]
All LM rails installed on the same plane have the same serial number printed on them. Of these, the LM rail marked "KB" at the end of the serial number is the reference side, and the LM block has a reference surface finished to the specified accuracy, so it is used as the positioning side of the table. (Refer to Fig. 1)
Since "KB" is not displayed only in the case of average accuracy, any LM rail with the same number can be used as the reference side.

Fig. 2 Reference plane display

[Display of Reference Plane]
As shown in Fig. 2, the reference plane of the LM guide is displayed on the opposite side of the THK mark for the LM block and on the line drawing mark side of the LM rail. Please specify if you absolutely want to reverse the positional relationship between the reference surfaces of the LM rail and the LM block, or if you need to reverse the direction of the grease fitting.

Fig. 3. Display of combination of LM rails and LM blocks (Example: HSR-A type)

[Display of Combination of LM Rails and LM Blocks]
The serial numbers displayed on the LM rails and LM blocks used in combination are the same numbers. If you need to separate the LM block from the LM rail, make sure the same numbers are in the same orientation and then reassemble. (Fig. 3)

Fig. 4 Use of Joints

[Use of Joints]
When a long LM rail is ordered, 2 or more rails will be jointed together to the desired length. In this case, make sure that the joint match marks shown in Fig. 4 are correctly positioned to joint rails.
Also, when joining LM rails in parallel use of 2 axes, the 2 sets combined in parallel are manufactured so that they are axisymmetric (mirror-image type) combinations.
If a large load is applied near the joint of the LM rail, the LM rail may shift and a step may occur. Therefore, it is recommended to press the LM rail against the abutting surface with an adjustment screw, etc., at the joint, shorten the L dimension, and fix it securely. (Fig. 4) Contact THK for details.

Installation Procedure

Installation example when vibration impact acts on the machine, and stiffness and high accuracy are required

Installation of LM rails

1. Be sure to remove burrs, dents, dust, etc., on the mating machine mounting surface of the LM guide before assembling. (Fig. 6)
*) Since rust preventive oil is applied to the LM guide, wipe the reference surface with cleaning oil before use. Since the reference surface from which the rust preventive oil has been removed is prone to rust, it is recommended to apply spindle oil with low viscosity.
2. Gently place the LM rail on the base and temporarily tighten the bolts so that the LM rail is lightly in contact with the mounting surface. (The line drawing mark side of the LM rail is abutted against the horizontal reference surface of the base.) (Fig. 7)
*) Use clean mounting bolts to fix the LM guide. Also, when inserting bolts into the mounting holes of the LM rail, check that the screw holes are not misaligned. (Fig. 8) Forcibly tightening the bolts with the holes misaligned may cause a decrease in accuracy.
3. Tighten the LM rail adjustment screw in order with a clamping force that is in close contact with the horizontal mounting surface. (Fig. 9)
4. Tighten the mounting bolts with the specified torque using a torque wrench. (Fig. 10)
*) Stable accuracy can be obtained by tightening the LM rail mounting bolts in order from the center position toward the shaft end.
5. Install the remaining LM rails in the same way to complete the installation of the LM rails.
6. Hammer in the cap into the bolt hole on the top of the LM rail so that it is on the same side.

Fig. 5 When vibration impact acts on the machine

Fig. 6 Checking the mounting surface

Fig. 7 Abutting of the reference plane

Fig. 8 Checking the play of bolts

Fig. 9 Tightening the adjustment screw

Fig. 10 Final tightening of mounting bolts

Fig. 11 LM block tightening procedure

Installation of LM block

1. Gently place the table on the LM block and temporarily tighten the mounting bolts.
2. Position the table by pressing the reference side LM block against the table side reference surface with an adjustment screw. (See B1-91 Fig. 5)
3. Finally tighten the mounting bolts on the reference side and driven side to complete the assembly.
*) Tightening the mounting bolts diagonally as shown in Fig. 11 will equalize the fixing of the table. This method does not take time to straighten the LM rail, and it does not require the dowel processing for fixing, so the assembly labor-hours are greatly reduced.

Installation of reference side LM rail
After temporarily tightening the mounting bolts, firmly press the mounting bolts against the horizontal reference with a compact vise, etc., and finally tighten the mounting bolts. Repeat this in order for each mounting bolt pitch. (Fig. 13)

Fig. 12 When the reference side LM rail does not have an adjustment screw

Fig. 13

Installation of driven side LM rail
The following method is recommended when mounting the driven side LM rail in parallel with the correctly mounted reference side LM rail.

Fig. 14

Straight edge method
After setting the straight edges lined up between the 2 axes parallel to the horizontal reference surface of the reference side LM rail with a dial gauge, while straightening the driven shaft with a dial gauge using the straight edge as a reference from the shaft end, fix the mounting bolts in sequence.

Fig. 15

Method by using parallelism of the table
Fix the 2 LM blocks on the reference side to the table (or temporary table for measurement), and temporarily tighten both the LM rail and LM block (1 pc.) on the driven side to the base and table. Place the dial gauge on the side of the LM block on the driven side from the dial stand fixed on the top of the table, move the table from the shaft end, and fix the bolts in sequence while aligning the LM rail on the driven side.

Fig. 16

How to follow the reference side LM rail
Place the table on the LM blocks of the properly mounted reference side LM rail and the temporarily tightened driven side LM rail, and finally tighten 1 of the 2 reference side LM blocks and the 2 driven side LM blocks with bolts. While temporarily tightening the remaining driven side LM blocks, finally tighten the mounting bolts of the driven side LM rails in sequence.

Fig. 17

Jig method
Using a jig as shown in Fig. 17, finally tighten the mounting bolts in order from one end for each mounting pitch while setting the parallelism of the driven side reference plane to the side reference plane on the reference side.

Installation example when the reference side LM rail does not have a side contact surface

Installation of reference side LM rail

Fig. 18

Fig. 19

How to use a temporary reference plane
There is a method to straighten the LM rail from the shaft end using the reference surface provided near the LM rail mounting part of the base, but in this case, 2 LM blocks must be joined together and attached to a measurement plate as shown in Fig. 19.

Fig. 20

Straight edge method
After temporarily tightening the mounting bolts, finally tighten the mounting bolts while straightening the side reference surface of the LM rail from the shaft end with a dial gauge using the straight edge as a reference as shown in Fig. 20.

HR type assembly procedure
The following procedure is recommended for installing the HR type.

1. Apply oil stones to the LM rail mounting surface of the base to remove burrs, knots, etc. (Fig. 21)
2. Using a compact vise or the like on the mounting surface of the base, press it so that it is in close contact with the reference surface, and tighten the mounting bolts with the recommended torque (see B1-101). (Fig. 22)
a. Check if any of the bolts has a sinking.
b. Tighten the bolts in order from the center to both ends using a torque wrench.
3. Set the LM block on the table and install it on the LM rail. At this time, temporarily tighten the mounting bolts of the LM block.
4. Tighten the clearance adjustment screws alternately to adjust the clearance. If sufficient preload is applied to obtain high stiffness, it is controlled by the tightening torque or rolling resistance value.
a. It is good to have 3 clearance adjustment screws for each LM block as shown in Fig. 23.
b. Good results can be obtained by setting the tightening torque of the 3 clearance adjustment screws to about 90%, which is slightly weaker than the center screw.
5. While moving the table, gradually tighten the 2 LM block mounting bolts that were temporarily tightened alternately to fix the LM block. (Fig. 24)

Fig. 21

Fig. 22

Fig. 23

Fig. 24

Clearance adjustment example
Design the clearance adjustment screw to push the center of the side of the LM block.

Normally, an adjustment screw is used to press the LM block.

If you need high precision and high stiffness, use tapered gibs 1 and 2.

A type that adjusts the clearance with an eccentric pin is also manufactured.

GSR Type Assembly Procedure
The procedure for assembling the GSR type is shown below.

1. Place the table against the reference surface of the LM block and finally tighten it to fix it. There are abutting surfaces on both sides of the table. (Fig. 25)
2. Place the LM rail A on the base and align the rail with a straight edge. Use a torque wrench to finally tighten. (Fig. 26)
3. Temporarily fix the LM rail B to the base and insert the block. Temporarily tighten while pressing the LM rail B against the block side. (Fig. 27)
4. Stroke the table several times, and finally tighten the LM rail B with a torque wrench while letting the LM block fit. (Fig. 28) If the number of assembly is large, it is easy to install them while keeping the parallelism of the LM rail after manufacturing a jig as shown in Fig. 29.

Fig. 25

Fig. 26

Fig. 27

Fig. 29

JR Type Assembly Procedure

When using in parallel with the axes as shown in Fig. 30, after fixing 1 axis to the base, set the dial gauge on the upper surface of the LM block, and apply it to the side and upper surfaces of the LM rail for the remaining 1 axis to perform parallel and level adjustment at the same time, and install them.

When using with LM rail joint specifications, metal fittings as shown in Fig. 31 are available, so please specify that. (The rail is tapped for mounting the joint metal fittings.)

Mounting method

1. Temporarily tighten the rail presser bolts.
2. Fix rail A and joint fittings with bolts C and D.
3. Apply a dial gauge to the side surface G of the joint of rails A and B, and adjust the left and right steps with the bolt E and set screw F on the rail B side. When the bolt E is tightened, the rail B moves to the b side. when the set screw F is tightened, the rail B moves to the a side.
4. After adjusting with the set screw F, fix the set screw F with the nut.
5. Adjust and fix the vertical direction with the rail presser.

When welding rails, it is ideal for fix the welding location with a compact vise as shown in Fig. 32 above. The following welding conditions are recommended for welding. (Be careful not to spatter the rolling surface of the LM rail during welding.)

[Welding Conditions]
Preheating temperature: 200°C
Postheating temperature: 350°C
*) There is a risk of re-hardening if the temperature exceeds 750°C.

[For Shielded Metal Arc Welding]
Welding rod: LB52 Kobe Steel, Ltd.

[For Carbon Dioxide Arc Welding]
Wire: YGW12
Current: 200 A

To install the LM rail of the R guide, it is recommended that you provide a butt (or a pin, etc.,) on the reference surface side (inside) of the LM rail, and press the LM rail against the butt surface and hold it with a board from the counter-reference surface side.

Accuracy measurement method after mounting

Fig. 35 Accuracy measurement method after mounting

When measuring the running accuracy of 1 axis
When measuring the running accuracy of the LM block, stable accuracy can be obtained by using 2 LM blocks and fixing them to the inspection plate as shown in Fig. 35. Also, when using a dial gauge, it is better to place the straight edge as close as possible to the LM block for accurate measurement.

Installation of LM guide

For the high-precision LM rails of the LM guide, the rolling surface is finished by grinding and accuracy is inspected with the rails tightened with bolts. When mounting on the machine main body, the screw tightening torque values shown in tables 1 and 2 are recommended.

Cautions/prohibitions

[Handling]

1. When transporting heavy products (20 kg or more), use 2 or more people or transport equipment. It may cause injury or damage.
2. Do not disassemble each part. It may cause loss of function.
3. Please note that if you tilt the LM block and LM rail, it may fall under its own weight.
4. Do not drop or hit the LM guide. It may cause injury or damage. Also, if it is impacted, it may lose its function even if it does not look damaged on its external appearance.
5. When assembling, do not pull out the LM block from the LM rail.
6. Please note that if you get your hands in the mounting holes of the LM rail, you may get injured by pinching your hands with the LM block.
7. When handling the product, wear protective gloves, safety shoes, etc., as necessary to ensure safety.

[Precautions for Use]

1. Be careful not to let contaminants such as chips and coolant flow in. It will cause damage.
2. If the product is used in an environment where chips, coolant, corrosive solvent, water, etc., may flow into the product, use bellows or a cover to avoid the inflow into the product.
3. Avoid using above 80°C. Except for heat-resistant specifications, if this temperature is exceeded, resin and rubber parts may be deformed or damaged.
4. If contaminants such as chips adhere, clean it and then refill the lubricant.
5. In the case of a fine stroke, it is difficult for an oil film to form on the contact surface between the rolling surface and the rolling element, which may cause fretting, so use grease with excellent fretting resistance. It is also recommended to form an oil film on the rolling surface and rolling element by periodically applying a stroke movement of about the length of the LM block.
6. Do not force the positioning parts (pins, keys, etc.,) into the product. Indentations may occur on the rolling surface, causing loss of function.
7. If it is unavoidable to insert or remove the LM block from the LM rail, use the insertion/removal jig. (The insertion/removal jig is not included as standard, so please contact THK when using it.)
8. When using the insertion/removal jig, make sure that the flange of the LM rail and the flange of the jig are in close contact with each other, and insert the jig with the LM rail and the jig in parallel.
9. If the LM block is inserted while tilted, contaminants may flow in, internal parts may be damaged, and the rolling elements may fall.
10. If the LM block is inserted into the LM rail and used with the rolling element removed, it may cause premature damage.
11. If the rolling element falls off the LM block, do not use it as it is and contact THK.
12. If the end plate is damaged due to an accident, the ball may fall off and the LM block may come off the LM rail and fall. If the LM guide is used while hanging upside down, take measures such as adding a fall prevention safety mechanism.
13. Insufficient stiffness and accuracy of the mounting parts will cause the bearing load to be locally concentrated and significantly reduce bearing performance. Therefore, carefully consider the stiffness and accuracy of the housing and base, and the strength of the fixing bolts.
14. If you want to remove the LM block from the LM rail and then reassemble it, contact THK for an LM block extraction/insertion jig to facilitate assembly.

[Lubrication]

1. Wipe off the rust preventive oil well and fill it with lubricant before use.
2. Avoid using a mixture of different lubricants. Even if the greases have the same type of thickener, they may adversely affect each other due to different additives, etc.
3. When using in a special environment such as a place where vibration always acts, a cleanroom, vacuum, low temperature / high temperature, please use grease suitable for the specifications/environment.
4. When lubricating a product that does not have a grease fitting or lubrication hole, apply the lubricant directly to the rolling surface and perform a break-in stroke several times to allow grease to enter inside.
5. The cone penetration of grease changes depending on the temperature. Please note that the sliding resistance of the LM guide will change as the cone penetration changes.
6. After lubrication, the sliding resistance of the LM guide may increase due to the stirring resistance of the grease. Be sure to run-in and let the grease spread sufficiently before operating the machine.
7. Immediately after lubrication, excess grease may scatter around, so wipe it off if necessary.
8. Grease deteriorates in properties over time and its lubrication performance deteriorates, so it is necessary to check and replenish the grease according to the frequency of use.
9. The greasing interval varies depending on the usage conditions and the operating environment, but please refuel with a mileage of 100 km (3 to 6 months) as a guide. Please set the final greasing interval and amount on the actual machine.
10. It may be difficult for the lubricant to reach the rolling surface unless the mounting posture is horizontal. Please refer to B1-28 for mounting posture and B24-2 for lubrication.
11. When using with lubricant oil, the lubricant oil may not be distributed depending on the mounting posture of the LM block, so please contact THK in advance.

[Storage]
Store the LM guide in manufacturer's packaging and packing, with avoiding high temperatures, low temperatures, and high humidity, and storing it in a horizontal position. For products that have been stored for a long period of time, the internal lubricant may have deteriorated over time, so re-lubricate the product before use.
[Waste]
Please dispose of the product appropriately as industrial waste.

Cautions/prohibitions

[Order Unit]
Please note that the counting method of 1 set differs depending on the type of LM guide. Please check the nominal model number configuration example and notes.

SHS25C2SSC1 + 640 L 1 set, SHS25C2SSC1 + 640 L-II 2 sets

HR2555UU + 600 L 1 set

GSR25T2UU + 1060 L 2 sets

4SCR25UU + 1200/1000LP 1 set

HMG15A2UUC1 + 1000LT + 60/150R6T + 60/300R6T-II 2 sets

*) When ordering the HMG type, please attach a reference drawing showing the arrangement of the LM block and LM rail.

[Mounting Posture and Lubrication Method]
When ordering, be sure to inform THK of the mounting position of the LM guide and the position of the grease fitting / piping joint to be mounted on each LM block.
Please refer to A1-12 for mounting posture and A24-2 for lubrication.
[About the Support Status of Options]
Depending on the nominal model number, the support status of options will differ, so please check before ordering.
[Maximum Production Length of LM Rail]
Please contact THK as the maximum manufacturing length of LM rails may be limited if the accuracy class is high.

Product comparison information

Selection support information

Types of LM guides
LM guides are standardized in a wide variety of formats and dimensions so that you can select the ideal product for every application. It is a unit structure that can obtain high running accuracy without gaps by simply attaching it to a flat surface with bolts, and has many achievements and know-how in a wide range of applications.

Selection of choice

: 30; 60; 90

Part Number
HSR15A[1,2,3,4,5,6,7,8,9,NLL]+[1481-3000/1]L
HSR15A[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1481-3000/1]L
HSR15B[1,2,3,4,5,6,7,8,9,NLL]+[1481-3000/1]L
HSR15B[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1481-3000/1]L
HSR15R[1,2,3,4,5,6,7,8,9,NLL]+[1481-3000/1]L
HSR15R[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1481-3000/1]L
HSR15R[1,2,3,4]+[73-2920/1]L
HSR15R[1,2,3,4][SS,UU]+[73-2920/1]L
HSR20A[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR20A[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR20B[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR20B[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR20LA[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR20LA[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR20LB[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR20LB[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR20LR[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR20LR[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR20LR[1,2,3,4]+[103-2920/1]L
HSR20LR[1,2,3,4][SS,UU]+[103-2920/1]L
HSR20R[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR20R[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR20R[1,2,3,4]+[87-2920/1]L
HSR20R[1,2,3,4][SS,UU]+[87-2920/1]L
HSR25A[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR25A[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR25B[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR25B[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR25LA[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR25LA[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR25LB[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR25LB[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR25LR[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR25LR[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR25LR[1,2,3,4]+[116-2920/1]L
HSR25LR[1,2,3,4][SS,UU]+[116-2920/1]L
HSR25R[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR25R[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR25R[1,2,3,4]+[97-2920/1]L
HSR25R[1,2,3,4][SS,UU]+[97-2920/1]L
HSR30A[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR30A[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR30B[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR30B[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR30LA[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR30LA[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR30LB[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR30LB[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR30LR[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR30LR[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR30LR[1,2,3,4]+[134-2920/1]L
HSR30LR[1,2,3,4][SS,UU]+[134-2920/1]L
HSR30R[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR30R[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR30R[1,2,3,4]+[111-2920/1]L
HSR30R[1,2,3,4][SS,UU]+[111-2920/1]L
HSR35A[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR35A[1,2,3,4,5,6,7,8,9,NLL][SS,UU]+[1961-3000/1]L
HSR35B[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR35B[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR35LA[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR35LA[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR35LB[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR35LB[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR35LR[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR35LR[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR35LR[1,2,3,4]+[148-2920/1]L
HSR35LR[1,2,3,4][SS,UU]+[148-2920/1]L
HSR35R[1,2,3,4,5,6,7,8,9,NLL]+[1961-3000/1]L
HSR35R[1,2,3,4,5,6,7,8,9,NLL]SS+[1961-3000/1]L
HSR35R[1,2,3,4]+[123-2920/1]L
HSR35R[1,2,3,4][SS,UU]+[123-2920/1]L

Standard Unit Price	Minimum order quantity	Days to Ship	Rail Length L (mm)	Block Type	Rail Width W1 (mm)	Mounting Height M (mm)	Nominal Part Number	Radial Clearance	Accuracy Grade	No. of Blocks Used On The Same Rail	Basic Load Rating Dynamic Rating C (N)	Basic Load Rating Static Rating Co (N)	Allowable Static Moment MA (N⋅m)	Allowable Static Moment MB (N⋅m)	Allowable Static Moment MC (N⋅m)	Block Mounting Hole Pitch (Width Direction) (mm)	Block Mounting Hole Pitch (Length Direction) (mm)	Block Mounting Hole Diameter	Rail Mounting Hole Pitch (mm)	Rail Mounting Hole Diameter	Block External Dimension W (mm)	Block External Dimension L (mm)	Mounting hole for blocks	Mounting Hole Dimension S (M)	Mounting Hole Dimension H (ø)	Mounting Hole Screw Depth (mm)	Block Dimension L1 (mm)	Symbols for Dust Resistance	Dust Resistance Symbol
-	1 Piece(s)	7 Day(s) or more	1481 ～ 3000	Wide	15	24	15	Normal	Standard Grade	1 ～ 9	10900	15700	94.5	94.5	99.8	-	-	-	-	-	47	56.6	Tapped Holes	M5	-	Through	38.8	NA	-
-	1 Piece(s)	7 Day(s) or more	1481 ～ 3000	Wide	15	24	15	Normal	Standard Grade	1 ～ 9	10900	15700	94.5	94.5	99.8	-	-	-	-	-	47	56.6	Tapped Holes	M5	-	Through	38.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1481 ～ 3000	Wide	15	24	15	Normal	Standard Grade	1 ～ 9	10900	15700	94.5	94.5	99.8	-	-	-	-	-	47	56.6	Drilled Hole	-	4.5	Through	38.8	NA	-
-	1 Piece(s)	7 Day(s) or more	1481 ～ 3000	Wide	15	24	15	Normal	Standard Grade	1 ～ 9	10900	15700	94.5	94.5	99.8	-	-	-	-	-	47	56.6	Drilled Hole	-	4.5	Through	38.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1481 ～ 3000	Standard	15	28	15	Normal	Standard Grade	1 ～ 9	10900	15700	94.5	94.5	99.8	-	-	-	-	-	34	56.6	Tapped Holes	M4	-	5	38.8	NA	-
-	1 Piece(s)	7 Day(s) or more	1481 ～ 3000	Standard	15	28	15	Normal	Standard Grade	1 ～ 9	10900	15700	94.5	94.5	99.8	-	-	-	-	-	34	56.6	Tapped Holes	M4	-	5	38.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	6 Day(s) or more	73 ～ 2920	Standard	15	28	15	Normal	Standard Grade	1 ～ 4	10900	15700	94.5	94.5	99.8	26	26	4	60	4.5	34	56.6	Tapped Holes	M4	-	5	38.8	NA	-
-	1 Piece(s)	6 Day(s) or more	73 ～ 2920	Standard	15	28	15	Normal	Standard Grade	1 ～ 4	10900	15700	94.5	94.5	99.8	26	26	4	60	4.5	34	56.6	Tapped Holes	M4	-	5	38.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	19800	27400	218	218	235	-	-	-	-	-	63	74	Tapped Holes	M6	-	Through	50.8	NA	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	19800	27400	218	218	235	-	-	-	-	-	63	74	Tapped Holes	M6	-	Through	50.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	19800	27400	218	218	235	-	-	-	-	-	63	74	Drilled Hole	-	6	Through	50.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	19800	27400	218	218	235	-	-	-	-	-	63	74	Drilled Hole	-	6	Through	50.8	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	23900	35800	363	363	307	-	-	-	-	-	63	90	Tapped Holes	M6	-	Through	66.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	23900	35800	363	363	307	-	-	-	-	-	63	90	Tapped Holes	M6	-	Through	66.8	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	23900	35800	363	363	307	-	-	-	-	-	63	90	Drilled Hole	-	6	Through	66.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	20	30	20	Normal	Standard Grade	1 ～ 9	23900	35800	363	363	307	-	-	-	-	-	63	90	Drilled Hole	-	6	Through	66.8	-	Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	20	30	20	Normal	Standard Grade	1 ～ 9	23900	35800	363	363	307	-	-	-	-	-	44	90	Tapped Holes	M5	-	6	66.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	20	30	20	Normal	Standard Grade	1 ～ 9	23900	35800	363	363	307	-	-	-	-	-	44	90	Tapped Holes	M5	-	6	66.8	-	Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	103 ～ 2920	Standard	20	30	20	Normal	Standard Grade	1 ～ 4	23900	35800	363	363	307	32	50	5	60	4.5	44	90	Tapped Holes	M5	-	6	66.8	NA	-
-	1 Piece(s)	6 Day(s) or more	103 ～ 2920	Standard	20	30	20	Normal	Standard Grade	1 ～ 4	23900	35800	363	363	307	32	50	5	60	4.5	44	90	Tapped Holes	M5	-	6	66.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	20	30	20	Normal	Standard Grade	1 ～ 9	19800	27400	218	218	235	-	-	-	-	-	44	74	Tapped Holes	M5	-	6	50.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	20	30	20	Normal	Standard Grade	1 ～ 9	19800	27400	218	218	235	-	-	-	-	-	44	74	Tapped Holes	M5	-	6	50.8	-	End Seal / Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	87 ～ 2920	Standard	20	30	20	Normal	Standard Grade	1 ～ 4	19800	27400	218	218	235	32	36	5	60	4.5	44	74	Tapped Holes	M5	-	6	50.8	NA	-
-	1 Piece(s)	6 Day(s) or more	87 ～ 2920	Standard	20	30	20	Normal	Standard Grade	1 ～ 4	19800	27400	218	218	235	32	36	5	60	4.5	44	74	Tapped Holes	M5	-	6	50.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	27600	36400	334	324	366	-	-	-	-	-	70	83.1	Tapped Holes	M8	-	Through	59.5	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	27600	36400	334	324	366	-	-	-	-	-	70	83.1	Tapped Holes	M8	-	Through	59.5	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	27600	36400	334	324	366	-	-	-	-	-	70	83.1	Drilled Hole	-	7	Through	59.5	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	27600	36400	334	324	366	-	-	-	-	-	70	83.1	Drilled Hole	-	7	Through	59.5	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	35200	51600	627	627	518	-	-	-	-	-	70	102.2	Tapped Holes	M8	-	Through	78.6	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	35200	51600	627	627	518	-	-	-	-	-	70	102.2	Tapped Holes	M8	-	Through	78.6	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	35200	51600	627	627	518	-	-	-	-	-	70	102.2	Drilled Hole	-	7	Through	78.6	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	23	36	25	Normal	Standard Grade	1 ～ 9	35200	51600	627	627	518	-	-	-	-	-	70	102.2	Drilled Hole	-	7	Through	78.6	-	Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	23	40	25	Normal	Standard Grade	1 ～ 9	35200	51600	627	627	518	-	-	-	-	-	48	102.2	Tapped Holes	M6	-	8	78.6	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	23	40	25	Normal	Standard Grade	1 ～ 9	35200	51600	627	627	518	-	-	-	-	-	48	102.2	Tapped Holes	M6	-	8	78.6	-	Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	116 ～ 2920	Standard	23	40	25	Normal	Standard Grade	1 ～ 4	35200	51600	627	627	518	35	50	8	60	7	48	102.2	Tapped Holes	M6	-	8	78.6	NA	-
-	1 Piece(s)	6 Day(s) or more	116 ～ 2920	Standard	23	40	25	Normal	Standard Grade	1 ～ 4	35200	51600	627	627	518	35	50	8	60	7	48	102.2	Tapped Holes	M6	-	8	78.6	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	23	40	25	Normal	Standard Grade	1 ～ 9	27600	36400	334	324	366	-	-	-	-	-	48	83.1	Tapped Holes	M6	-	8	59.5	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	23	40	25	Normal	Standard Grade	1 ～ 9	27600	36400	334	324	366	-	-	-	-	-	48	83.1	Tapped Holes	M6	-	8	59.5	-	End Seal / Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	97 ～ 2920	Standard	23	40	25	Normal	Standard Grade	1 ～ 4	27600	36400	334	324	366	35	35	8	60	7	48	83.1	Tapped Holes	M6	-	8	59.5	NA	-
-	1 Piece(s)	6 Day(s) or more	97 ～ 2920	Standard	23	40	25	Normal	Standard Grade	1 ～ 4	27600	36400	334	324	366	35	35	8	60	7	48	83.1	Tapped Holes	M6	-	8	59.5	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	40500	53700	599	599	652	-	-	-	-	-	90	98	Tapped Holes	M10	-	Through	70.4	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	40500	53700	599	599	652	-	-	-	-	-	90	98	Tapped Holes	M10	-	Through	70.4	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	40500	53700	599	599	652	-	-	-	-	-	90	98	Drilled Hole	-	9	Through	70.4	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	40500	53700	599	599	652	-	-	-	-	-	90	98	Drilled Hole	-	9	Through	70.4	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	48900	70200	995	995	852	-	-	-	-	-	90	120.6	Tapped Holes	M10	-	Through	93	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	48900	70200	995	995	852	-	-	-	-	-	90	120.6	Tapped Holes	M10	-	Through	93	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	48900	70200	995	995	852	-	-	-	-	-	90	120.6	Drilled Hole	-	9	Through	93	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	28	42	30	Normal	Standard Grade	1 ～ 9	48900	70200	995	995	852	-	-	-	-	-	90	120.6	Drilled Hole	-	9	Through	93	-	Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	28	45	30	Normal	Standard Grade	1 ～ 9	48900	70200	995	995	852	-	-	-	-	-	60	120.6	Tapped Holes	M8	-	10	93	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	28	45	30	Normal	Standard Grade	1 ～ 9	48900	70200	995	995	852	-	-	-	-	-	60	120.6	Tapped Holes	M8	-	10	93	-	Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	134 ～ 2920	Standard	28	45	30	Normal	Standard Grade	1 ～ 4	48900	70200	995	995	852	40	60	8	80	9	60	120.6	Tapped Holes	M8	-	10	93	NA	-
-	1 Piece(s)	6 Day(s) or more	134 ～ 2920	Standard	28	45	30	Normal	Standard Grade	1 ～ 4	48900	70200	995	995	852	40	60	8	80	9	60	120.6	Tapped Holes	M8	-	10	93	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	28	45	30	Normal	Standard Grade	1 ～ 9	40500	53700	599	599	652	-	-	-	-	-	60	98	Tapped Holes	M8	-	10	70.4	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	28	45	30	Normal	Standard Grade	1 ～ 9	40500	53700	599	599	652	-	-	-	-	-	60	98	Tapped Holes	M8	-	10	70.4	-	End Seal / Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	111 ～ 2920	Standard	28	45	30	Normal	Standard Grade	1 ～ 4	40500	53700	599	599	652	40	40	8	80	9	60	98	Tapped Holes	M8	-	10	70.4	NA	-
-	1 Piece(s)	6 Day(s) or more	111 ～ 2920	Standard	28	45	30	Normal	Standard Grade	1 ～ 4	40500	53700	599	599	652	40	40	8	80	9	60	98	Tapped Holes	M8	-	10	70.4	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	53900	70200	895	895	1050	-	-	-	-	-	100	109.4	Tapped Holes	M10	-	Through	80.4	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	53900	70200	895	895	1050	-	-	-	-	-	100	109.4	Tapped Holes	M10	-	Through	80.4	-	End Seal / Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	53900	70200	895	895	1050	-	-	-	-	-	100	109.4	Drilled Hole	-	9	Through	80.4	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	53900	70200	895	895	1050	-	-	-	-	-	100	109.4	Drilled Hole	-	9	Through	80.4	-	Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	65000	91700	1490	1490	1370	-	-	-	-	-	100	134.8	Tapped Holes	M10	-	Through	105.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	65000	91700	1490	1490	1370	-	-	-	-	-	100	134.8	Tapped Holes	M10	-	Through	105.8	-	Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	65000	91700	1490	1490	1370	-	-	-	-	-	100	134.8	Drilled Hole	-	9	Through	105.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Wide	34	48	35	Normal	Standard Grade	1 ～ 9	65000	91700	1490	1490	1370	-	-	-	-	-	100	134.8	Drilled Hole	-	9	Through	105.8	-	Seal (End + Side)
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	34	55	35	Normal	Standard Grade	1 ～ 9	65000	91700	1490	1490	1370	-	-	-	-	-	70	134.8	Tapped Holes	M8	-	12	105.8	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	34	55	35	Normal	Standard Grade	1 ～ 9	65000	91700	1490	1490	1370	-	-	-	-	-	70	134.8	Tapped Holes	M8	-	12	105.8	-	Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	148 ～ 2920	Standard	34	55	35	Normal	Standard Grade	1 ～ 4	65000	91700	1490	1490	1370	50	72	8	80	9	70	134.8	Tapped Holes	M8	-	12	105.8	NA	-
-	1 Piece(s)	6 Day(s) or more	148 ～ 2920	Standard	34	55	35	Normal	Standard Grade	1 ～ 4	65000	91700	1490	1490	1370	50	72	8	80	9	70	134.8	Tapped Holes	M8	-	12	105.8	End Seal / Seals (End + Side)	-
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	34	55	35	Normal	Standard Grade	1 ～ 9	53900	70200	895	895	1050	-	-	-	-	-	70	109.4	Tapped Holes	M8	-	12	80.4	-	None
-	1 Piece(s)	7 Day(s) or more	1961 ～ 3000	Standard	34	55	35	Normal	Standard Grade	1 ～ 9	53900	70200	895	895	1050	-	-	-	-	-	70	109.4	Tapped Holes	M8	-	12	80.4	-	Seal (End + Side)
-	1 Piece(s)	6 Day(s) or more	123 ～ 2920	Standard	34	55	35	Normal	Standard Grade	1 ～ 4	53900	70200	895	895	1050	50	50	8	80	9	70	109.4	Tapped Holes	M8	-	12	80.4	NA	-
-	1 Piece(s)	6 Day(s) or more	123 ～ 2920	Standard	34	55	35	Normal	Standard Grade	1 ～ 4	53900	70200	895	895	1050	50	50	8	80	9	70	109.4	Tapped Holes	M8	-	12	80.4	End Seal / Seals (End + Side)	-

Basic Information

Rail Type	Standard	Set / Single Item	Set	Material	Carbon Steel
Ball Arrangement	4 Rows of Circular	Retainer	No	Rolling Element	Ball
Number of Block Mounting Holes(holes)	4

Configure

72 Part Numbers

View Part Numbers

Configure Remaining Specifications

Completed

Specification/Dimensions

Rail Length L(mm)
[73-3000/1mm Unit(s)]
Clear
Block Type
- Standard
- Wide
Clear
Rail Width W1(mm)
15

20

23

28

34
Clear
Mounting Height M(mm)
24

28

30

36

40

42

45

48

55
Clear
Nominal Part Number
15

20

25

30

35
Clear
Radial Clearance
- Normal
Clear
Accuracy Grade
- Standard Grade
Clear
No. of Blocks Used On The Same Rail
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
Clear
Block Mounting Hole Pitch (Width Direction)(mm)
26

32

35

38

40

50

53

57

72

82
Clear
Block Mounting Hole Pitch (Length Direction)(mm)
26

30

35

36

40

45

50

52

60

62

72
Clear
Block Mounting Hole Diameter
4

4.5

5

6

8

10
Clear
Rail Mounting Hole Pitch(mm)
60

80
Clear
Rail Mounting Hole Diameter
4.5

7

9
Clear
Block External Dimension W(mm)
34

44

47

48

60

63

70

90

100
Clear
Block External Dimension L(mm)
56.6

74

74.6

83.1

90

98

102.2

109.4

120.6

134.8
Clear
Mounting hole for blocks
- Drilled Hole
- Tapped Holes
- Tapped hole
Clear
Mounting Hole Dimension S(M)
M4

M5

M6

M8

M10
Clear
Mounting Hole Dimension H(ø)
4.5

6

7

9
Clear
Mounting Hole Screw Depth(mm)
5

6

8

10

12

Through
Clear
Block Dimension L1(mm)
38.8

50.8

56.8

59.5

66.8

70.4

78.6

80.4

93

105.8
Clear
Symbols for Dust Resistance
- End Seal
- NA
- Seals (End + Side)
Clear
Dust Resistance Symbol
- End Seal
- None
- Seal (End + Side)
Clear
type
- HSR-A
- HSR-B
- HSR-C
- HSR-LA
- HSR-LB
- HSR-LC
- HSR-LR
- HSR-R
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

6 Day(s) or Less

7 Day(s) or Less
Clear

Specify Alterations

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Additional Products in this Category

Customers Who Viewed This Item Also Viewed

Full-Ball Type LM Guide, International Standard, HSR Type
THK

Days to Ship : 13 Day(s) or more
[Short Delivery Size] Caged Ball LM Guide, International Standard, SHS Type
THK

Days to Ship : 6 Day(s) or more
[Short Delivery Size] Caged Ball LM Guide, Radial Type, SSR Type
THK

Days to Ship : 7 Day(s) or more
[Single Rail] Full-Ball Type LM Guide, International Standard, HSR Type
THK

Days to Ship : 6 Day(s) or more
[Individual Block Units] Full-Ball Type LM Guide, International Standard, HSR Type
THK

Standard Price : MYR 368.65-

Days to Ship : 4 Day(s) or more
Caged Ball LM Guide, International Standard, SHS Type
THK

Days to Ship : 13 Day(s) or more
Full-Ball Type LM Guide, Radial Type, SR Model
THK

Days to Ship : 7 Day(s) or more
[Short Delivery Size] Caged Ball LM Guide, Miniature, SRS Type
THK

Days to Ship : 4 Day(s) or more
[Individual Block Units] Caged Ball LM Guide, International Standard, SHS Type
THK

Standard Price : MYR 439.18-

Days to Ship : 4 Day(s) or more
Caged Ball LM Guide, Radial Type, SSR Type
THK

Days to Ship : 13 Day(s) or more
[Single Rail] Caged Ball LM Guide, International Standard, SHS Type
THK

Days to Ship : 6 Day(s) or more
[Individual Block Units] Caged Ball LM Guide, Radial Type, SSR Type
THK

Standard Price : MYR 502.44-

Days to Ship : 4 Day(s) or more

back next

Tech Support

Factory Automation, Electronics, Tools, & MRO (Maintenance, Repair and Operations): Tel：(60) 3 7890 6399; 9:00am - 6:00pm (Monday - Friday)
9:00am - 1:00pm (Saturday); Technical Inquiry

Top of the page

Payment Method

Credit Card
Bank Transfer

About MISUMI

About this Website

Useful Tools

Customer Service

Social Media

MISUMI Contact 9am – 6pm (Mon – Fri) * Order cut-off time is 5pm, 9am – 1pm(Sat) * Order cut-off time is 12pm

Tel: (60) 3 7890 6399

Inquiry

All Categories

Categories

Search by Application

Brands

Message from MISUMI

My Favorites

Settings

How can we improve?

[Short Delivery Size] Full-Ball Type LM Guide, International Standard, HSR Type (Part Numbers)

INDEX

Drawing

HSR-A type, HSR-LA type

HSR-B type, HSR-LB type

HSR-R type, HSR-LR type

HSR-C type, HSR-LC type

Basic specifications and features of the product

Structure and features

How to use and use cases

Installation procedure and maintenance

Installation of LM guide

Installation Procedure

Installation example when the reference side LM rail does not have a side contact surface

Accuracy measurement method after mounting

Installation of LM guide

Cautions/prohibitions

Cautions/prohibitions

Cautions/prohibitions

Cautions/prohibitions

Product comparison information

Selection support information

Selection support information

Basic Information

Configure

Specification/Dimensions

Rail Length L(mm)

Block Type

Rail Width W1(mm)

Mounting Height M(mm)

Nominal Part Number

Radial Clearance

Accuracy Grade

No. of Blocks Used On The Same Rail

Block Mounting Hole Pitch (Width Direction)(mm)

Block Mounting Hole Pitch (Length Direction)(mm)

Block Mounting Hole Diameter

Rail Mounting Hole Pitch(mm)

Rail Mounting Hole Diameter

Block External Dimension W(mm)

Block External Dimension L(mm)

Mounting hole for blocks

Mounting Hole Dimension S(M)

Mounting Hole Dimension H(ø)

Mounting Hole Screw Depth(mm)

Block Dimension L1(mm)

Symbols for Dust Resistance

Dust Resistance Symbol

type

CAD

Days to Ship

Specify Alterations

Additional Products in this Category

Customers Who Viewed This Item Also Viewed

Tech Support

Payment Method

About MISUMI

About this Website

Useful Tools

Customer Service

Social Media

MISUMI Contact 9am – 6pm (Mon – Fri) * Order cut-off time is 5pm, 9am – 1pm(Sat) * Order cut-off time is 12pm